The Art of Installation

Wallpaper Installation Guides

Good to know: A detailed instruction sheet will be included with your order, and every order comes with a complimentary squeegee.

Peel & Stick Wallpaper

Fast, clean application — no paste required.
Open / Close
Best results: install with a helper, work slowly, and keep humidity low. (A step-by-step instruction sheet is included with your order.)
  • Spirit level icon Spirit Level
  • Pencil icon Pencil
  • Squeegee icon Squeegee (included free)
  • Brush icon Brush (for dust/imperfections)
  • Step ladder icon Step Ladder
  • Cutter icon Cutter / Scissors (trimming)
  • Optional but helpful: sandpaper + a metal spatula (for smoothing and removing imperfections).
01

Get Ready

  • Remove the wallpaper from the packaging and release the roll so it isn’t tightly rolled.
  • Let it rest like this for at least 48 hours so it can adapt to the room conditions.
  • For removal: start from a corner and pull slowly. On painted walls, gentle heat from a blow dryer can reduce the risk of lifting paint.
02

Preparation

  • Freshly painted or primed walls must dry 2–7 days (depending on paint type) before installing.
  • Confirm you have the correct number of sheets and that designs/colors match. For murals, ensure sheet serial numbers form a sequence.
  • Fill holes and sand bumps so the wall is completely smooth. Avoid glossy walls (semi-matte only) and do not install over existing wallpaper.
  • Clean with a wet cloth and dry well. Do not use strong chemical cleaners. Wipe the wall with a damp cloth 24 hours prior to installation.
  • Remove electrical outlet covers and skirting boards.
  • Do not apply to unpainted walls, cracking paint, humidity spots, or textured finishes (knockdown, orange peel, popcorn).
03

Installation

  • Use a spirit level to draw a straight vertical line where you’ll start.
  • From the top of the sheet, peel off about 12 inches (30 cm) of the protective backing.
  • Do not drag or stretch the wallpaper (stretching can cause shrinking and uneven edges later).
  • Stick the first sheet exactly to your line. For murals, follow the serial number order.
  • Smooth from top to bottom, pushing air from the center out to the edges using the squeegee.
  • Continue peeling backing top-to-bottom while pressing and smoothing as you go.
  • Install further sheets edge-to-edge (no overlap). Match the pattern carefully.
04

Finalization

  • After 24 hours, repeat the smoothing process.
  • Trim excess at the top and bottom using scissors or a utility knife for clean edges.
  • Enjoy your new design.

Beautiful work.

Step back and admire it — your wall now has that polished, professionally-finished look.
Smooth, aligned, and made to last.

Pre-Pasted Wallpaper

Water-activated backing for a classic, secure finish.
Open / Close
A detailed instruction sheet will be included with your order.
  • Spirit level icon Spirit Level
  • Pencil icon Pencil
  • Squeegee icon Squeegee (included free)
  • Brush icon Wallpaper Brush / Sponge
  • Bucket icon Clean Water
  • Step ladder icon Step Ladder
  • Cutter icon Cutter / Scissors (trimming)
01

Get Ready

  • Remove from packaging, remove the sticker, and release the roll slightly so it isn’t tightly rolled.
  • Let it rest for at least 48 hours so it can adapt to the room conditions.
02

Preparation

  • Freshly painted or primed walls must dry 2–7 days (depending on paint type) before installing.
  • Confirm you have the correct number of sheets and that designs/colors match. For murals, ensure sheet serial numbers form a sequence.
  • Fill holes and sand bumps so the wall is completely smooth. Avoid glossy walls (semi-matte only) and do not install over existing wallpaper.
  • Clean with a wet cloth and dry well. Do not use strong chemical cleaners. Wipe the wall with a damp cloth 24 hours prior to installation.
  • Remove electrical outlet covers and skirting boards.
  • Do not apply to unpainted walls, cracking paint, humidity spots, or textured finishes (knockdown, orange peel, popcorn).
03

Installation

  • Draw a straight vertical guide line with a spirit level.
  • Activate the paste by wetting the back evenly (sponge/brush or sprayer). Let sit 10–15 seconds. Do not oversaturate.
  • Fold the wet panel loosely paste-side to paste-side and let it “book” for 1 minute.
  • Align the first sheet exactly to the guide line. Smooth from the center out to the edges.
  • Install additional sheets edge-to-edge (no overlap).
04

Finishing Touches

  • Press along seams and edges for a seamless appearance.
  • Use a damp sponge to remove any excess paste.
  • Trim excess at top/bottom using scissors or a utility knife.
  • Allow wallpaper to dry completely — then enjoy your new design.

That’s a wrap.

Clean seams, smooth finish, and a look that feels custom.
Enjoy the transformation — you did that.

Traditional Wallpaper

Glue-applied method for a timeless, long-lasting result.
Open / Close
A detailed instruction sheet will be included with your order.
  • Spirit level icon Spirit Level
  • Pencil icon Pencil
  • Brush icon Brush / Roller (for glue)
  • Bucket icon Wallpaper Glue
  • Squeegee icon Squeegee (included free)
  • Step ladder icon Step Ladder
  • Cutter icon Cutter / Scissors (trimming)
01

Get Ready

  • Remove from packaging, remove the sticker, and release the roll slightly so it isn’t tightly rolled.
  • Let it rest for at least 48 hours so it can adapt to the room conditions.
02

Preparation

  • Freshly painted or primed walls must dry 2–7 days (depending on paint type) before installing.
  • Confirm you have the correct number of sheets and that designs/colors match. For murals, ensure sheet serial numbers form a sequence.
  • Fill holes and sand bumps so the wall is completely smooth. Avoid glossy walls (semi-matte only) and do not install over existing wallpaper.
  • Clean with a wet cloth and dry well. Do not use strong chemical cleaners. Wipe the wall with a damp cloth 24 hours prior to installation.
  • Remove electrical outlet covers and skirting boards.
  • Do not apply to unpainted walls, cracking paint, humidity spots, or textured finishes (knockdown, orange peel, popcorn).
03

Installation

  • Use the spirit level to draw a straight vertical guide line where you’ll start.
  • Apply wallpaper glue to the wall using a brush or roller.
  • Stick the first sheet exactly to the drawn line and smooth air bubbles from the center out.
  • Install additional sheets edge-to-edge (no overlap).
  • After each new sheet, use a slightly moist sponge to remove glue from the edges.
04

Finalization

  • Trim excess at the top and bottom using scissors or a utility knife for clean edges.
  • Enjoy your new design.

Nicely done.

A classic finish with a designer feel.
Take a moment — your space just leveled up.